Search:

Type: Posts; User: neonz

Search: Search took 0.03 seconds.

  1. Replies
    3
    Views
    3,385

    I think the blades might have a slightly...

    I think the blades might have a slightly different angle, but the PWM feature is a primary differentiator between the two. If you need higher fan speeds, the XP is the way to go.
  2. I don't have the Asus Z170 mb, but do have an...

    I don't have the Asus Z170 mb, but do have an ASUS mb. Unless the Z170 has a specially designed CPU fan header, it should conform to the normal 4-pin cpu fan header design. There's only one way a...
  3. Replies
    3
    Views
    3,385

    You'll want to keep fans in positions 1 and 2, so...

    You'll want to keep fans in positions 1 and 2, so putting the XP's in there would be a good choice. Then use one of the original case fan in position 3 as intake and one in position 7 as exhaust,...
  4. Replies
    1
    Views
    6,229

    Enthoo Primo SE Green Z Build

    After a few months of research, hardware acquisition from multiple sources, and building this beast, my animation rig is basically finished.

    HARDWARE
    Case - Phanteks Enthoo Primo SE (Green)
    MB -...
  5. Here's two pictures of the radiator...

    Here's two pictures of the radiator configuration. The H90 is attached to CPU2, the H115i is attached to CPU1. With the pull fans added to the top, the CPU temps lower by about 3 degrees Celsius...
  6. Replies
    4
    Views
    4,411

    Doyll has a good list of items for Optimal...

    Doyll has a good list of items for Optimal Cooling on this thread.

    The only item in your setup that may hinder airflow is the back intake fan. This is typically set up to exhaust air out the back...
  7. Replies
    4
    Views
    4,411

    Without looking at the CFM measurements for each...

    Without looking at the CFM measurements for each fan, you will have 5 140mm fans on intake and 4 120mm on exhaust. The radiator is likely to impact exhaust CFM. All else being equal, assuming you...
  8. Replies
    1
    Views
    2,147

    Fan speed may be controlled by your motherboard...

    Fan speed may be controlled by your motherboard in the BIOS. On my ZPE10, that's how it works. Now, on the Primo, if you use the FAN Hub, you can connect the hub to the CPU fan header. Your...
  9. 617618 What we would need it a two-pin female...

    617618

    What we would need it a two-pin female connector to two-pin male connector (circled in picture) cable of about 100cm or so to really route nicely within the cable management areas. An LED...
  10. Finally finished the cable management and final...

    Finally finished the cable management and final hardware installation, so the doors are now on. Ambient room temperature is 29 degrees Celsius. I'm using LightWave 3D to render a complex animation...
  11. Replies
    3
    Views
    3,177

    BK indicates that the casing is black and the fan...

    BK indicates that the casing is black and the fan is white. The black/black version pictured is BKK. As for your question about the color, I'll just refer to them as lighter or darker than middle...
  12. Replies
    6
    Views
    4,459

    What case and CPU do you have? Pulling radiator...

    What case and CPU do you have? Pulling radiator heat into the case will tend to heat other items like GPU and other PCI hardware. What temps are you seeing for your CPU that would lead you to...
  13. Replies
    4
    Views
    5,051

    I know this is from 2013, but computer components...

    I know this is from 2013, but computer components are pretty standardized. Case fans that come pre-installed, especially the front ones, may differ as you describe. But purchasing standard case...
  14. PH-F140SP LED extension cable available for LED?

    I purchased a few LED fans for my Enthoo Primo case. All are connected to the LED cable connectors coming from the front of the case except for the fan at the bottom, back position in the case. The...
  15. Replies
    4
    Views
    4,369

    I have the Primo and purchased the same fans. ...

    I have the Primo and purchased the same fans. There are two connectors on it plus the manual LED button. One connector is for the fan header and the other is for the LED connector. It looks like...
  16. Asus Z10PE-D16 WS in the Enthoo Primo SE case. I...

    Asus Z10PE-D16 WS in the Enthoo Primo SE case. I was able to fit the H90 and H115i into the top radiator area. I checked into using two H100i's in the top, but I needed about 10-15mm more to do...
  17. Gotcha. I was under the impression that All In...

    Gotcha. I was under the impression that All In Ones were simply self-contained units with a pump, tubing, radiator, and fans that didn't require any configuration other than attaching to the case...
  18. Thanks for your input on Swiftech, Doyll. Since...

    Thanks for your input on Swiftech, Doyll. Since the H115i (or any 280mm AIO) mounted on the bottom might not have enough tubing length to adequately reach the 2nd CPU without a lot of tension due to...
  19. Recommendation for installing two Corsair H115i's in the Enthoo Primo SE?

    I'm putting together a custom build with the ASUS Z10PE-D16 WS motherboard and am trying to see if the Enthoo Primo has the ability to effectively use two Corsair H115i coolers (280mm). I believe...
Results 1 to 19 of 19