Search:

Type: Posts; User: Wachtel

Search: Search took 0.09 seconds.

  1. Replies
    2
    Views
    1,208

    The light on the front needs the SATA connector...

    The light on the front needs the SATA connector to work. I use this but not the LED-strip connector in my case.
  2. Replies
    3
    Views
    1,413

    The relevant measurements are the same. From what...

    The relevant measurements are the same. From what I've heard from people that have tried this it requires heavy modification of the motherboard plate. Removal of the rubber grommets was only the...
  3. A pricy solution, wouldn't a thin piece of black...

    A pricy solution, wouldn't a thin piece of black cardboard work?
  4. I picked up this case today. I'll put two good...

    I picked up this case today. I'll put two good 140 mm high airflow fans in front and one in back to start of. Should be plenty since this configuration worked well in the large Evolv ATX case.

    I'm...
  5. Replies
    1
    Views
    1,526

    No, it will not. I looked at this myself (didn't...

    No, it will not. I looked at this myself (didn't try it myself mind you) but the case needs modding to make it work. Found one who had done it by removing the rubber grommets and placing the board...
  6. Replies
    40
    Views
    25,509

    HardwareCanucks review: ...

    HardwareCanucks review:

    https://www.youtube.com/watch?v=-jWblNZ3Zsw
  7. Replies
    4
    Views
    2,939

    I would try three 120's in front as intake and...

    I would try three 120's in front as intake and one exhaust in back
  8. Replies
    4
    Views
    1,782

    Hi Bob43. You're not the only one with non-TG. I...

    Hi Bob43. You're not the only one with non-TG. I like the side-panel "door" system better than glass!
  9. Replies
    17
    Views
    7,592

    The Q-fan is easy to use when all fans are...

    The Q-fan is easy to use when all fans are plugged into the mobo itself. That's my setup on my Z170 board. If you want to use the PWM hub you must plug in the hub in the CPU_Fan header.
  10. Replies
    17
    Views
    7,592

    I have a Z179 Asus board. It's much easier to...

    I have a Z179 Asus board. It's much easier to plug in all the fans directly to the motherboard and adjust the fan speed curve in BIOS.
  11. Replies
    40
    Views
    25,509

    Must say I'm very tempted to switch from my Evolv...

    Must say I'm very tempted to switch from my Evolv ATX to this case. And update a few other things.
  12. Replies
    40
    Views
    25,509

    That case looked great! Hopefully they will take...

    That case looked great! Hopefully they will take this door solution and apply it on the ATX case.
  13. doyll, did you try this and how did it work out?

    doyll, did you try this and how did it work out?
  14. Replies
    4
    Views
    3,880

    I tested the hub a bit when I got the Evovl ATX....

    I tested the hub a bit when I got the Evovl ATX. The only fan connect you can use for the fan hub is the CPU_FAn. THE CPU_OPT is set at 100% if you don't use the CPU_FAN.
  15. Replies
    4
    Views
    3,504

    I have the regular Evolv ATX and that Phanteks...

    I have the regular Evolv ATX and that Phanteks logo keeps falling of. Very annoying.
  16. I've tried this myself without success. The only...

    I've tried this myself without success. The only way I could think of is to remove the HDD-cage first. This wasn't possible for me since one of the bottom screws has been replaced with a rivet. It...
Results 1 to 16 of 16